CNC Router Safe Operating Procedure

Version 2.0 · Updated November 2026 · For Bluey, Turbo and Trax CNC routers
Back to all instructions
About this procedureRead this procedure before you use your BlueCarve CNC router, and keep a printed copy near the machine. Items marked New were added in version 2.0. If you use a laser on your CNC, also read the Laser Safe Operating Procedure.

1. Required personal protective equipment

SignWhat to wear or do
Wear safety glasses to protect your eyes from dust and flying material.
Blue circle sign showing a head wearing earmuffsWear earmuffs or earplugs to protect your hearing from machine noise.
Turn on the dust extractor or wear a dust mask so you don’t breathe in wood dust.
New: MDF dust is very fine and harmful to breathe. When cutting MDF, use dust extraction at the cutter (a dust boot connected to an extractor) or wear a P2 respirator, and ideally both.
Blue circle sign showing a safety bootWear sturdy shoes to protect your feet from falling material or dropped objects.
Blue circle sign showing a protective apronWear close-fitting protective clothing so nothing can catch on moving parts.
Blue circle sign showing a head with long hair tied backTie back long or loose hair so it can’t catch on moving parts.
Remove rings and jewellery so they can’t catch on the machine or the material.
Prohibition sign over a person wearing headphonesPut away phones, headphones and other electronic devices so they don’t distract you or catch on moving parts.

2. Before you start

  1. Check that the work area and walkways are clear of slip and trip hazards.
  2. Make sure you know where all the machine’s controls are and how they work.
  3. New: Find the emergency stop button on your machine. The Turbo and Trax both have one. On older models, including older Bluey controllers, it is on the controller. On newer closed-loop or FluidNC models it is a separate emergency stop button. Test it before each session: press it, check that the machine won’t move, then release it (on the Turbo, turn the red knob clockwise to release it).
  4. Make sure all guards and safety devices are in place and secure.
  5. Use only material that is free of defects.
  6. Use the right size cutting bit for the job. Isolate the machine (switch off the router or spindle and the controller) before you make any adjustment to the cutter head or change a bit.
  7. Check that cutters are sharp and free of resin build-up and wear.
  8. Adjust the dust collector shroud or dust boot (where fitted) so it collects as much dust as possible.
  9. New: Clear chips and dust from the machine, the bed and the floor around it. Built-up dust and chips are a fire risk, especially near the spindle, the router motor and the controller.
  10. New (water-cooled spindles): Start the water pump and check that water is flowing back into the reservoir before you start the spindle. Never run a water-cooled spindle dry.
  11. Be aware of other people in the area and make sure it is clear before you start.

3. While operating

New: the emergency stop does not stop the spindleOn machines with a spindle, the VFD (the spindle’s speed controller) is not connected to the CNC controller. Pressing the emergency stop stops the machine’s movement, but the spindle keeps spinning. To stop the spindle, press STOP/RESET on the VFD or switch it off. On machines with a trim router, switch the router off at its own switch.
  1. Never program the CNC to work beyond the machine’s capacity.
  2. Check your toolpaths and CNC program before you start a job.
  3. Make sure sheet material (such as ply, acrylic, aluminium, foam or rubber) is secured to the bed before cutting or engraving.
  4. Keep every axis clear of obstructions while the machine is cutting or engraving.
  5. Never try to remove waste material or dust from the bed while the machine is running.
  6. Never leave the CNC running unattended.
  7. New (water-cooled spindles): Keep an eye on the water flow during the job. If the pump stops, stop the spindle at the VFD straight away.
New: electrical workChanging the spindle motor wiring (U/V/W) or the VFD’s mains wiring must be done by a licensed electrician, with the power isolated.

4. After use

  1. Switch the machine off and wait for the cutter bit to stop completely before you remove the material and waste. On a spindle machine, stop the spindle at the VFD first.
  2. New (water-cooled spindles): Turn the water pump off only after the spindle has stopped.
  3. Brush or vacuum the machine and work area clean so it is safe and tidy, and so dust and chips don’t build up.

5. Troubleshooting

ProblemCheck
The spindle keeps spinning after you press the emergency stopThis is expected: the VFD is not connected to the controller. Press STOP/RESET on the VFD to stop the spindle.
Turbo: Easel’s Carve button won’t turn greenThe emergency stop may be engaged. Turn the red knob clockwise to release it.
All motors stop suddenly and the controller shows a motor fault (closed-loop machines)The closed-loop motors turn all motors off when one has a critical fault, such as the gantry bumping into something. Find and clear the cause before you restart.
Dust is building up around the machineAdjust the dust shroud or boot so it sits correctly, check the extractor is on, and clean the machine after each job.
Need help?
Email adam@bluecarve.com.au with your machine model, size and a photo or short video of the problem. Owners also help each other in the BlueCarve owners group on Facebook.
0
0
Quote Request
Your cart is emptyReturn to Shop