Laser Safe Operating Procedure
Laser Safe Operating Procedure
About this procedureRead this procedure before you use your BluLaser, and keep a printed copy near the machine. Items marked New were added in version 2.0. The Router Safe Operating Procedure also applies to the CNC itself.
1. Required personal protective equipment
| Sign | What to wear or do |
|---|---|
| Wear laser safety glasses to protect your eyes from laser light. New: Glasses must be rated for the laser’s wavelength (445–465 nm) with an optical density of OD5 or higher at 445 nm (for both the 5 W and 10 W BluLaser), and certified to EN 207 or an equivalent standard. Ordinary safety glasses and sunglasses do not protect you. Everyone in the room needs their own pair. | |
![]() | Wear earmuffs or earplugs to protect your hearing from machine noise. |
| Turn on the fume extractor or wear a suitable mask so you don’t breathe in fumes. | |
![]() | Wear sturdy shoes to protect your feet from falling material or dropped objects. |
![]() | Wear close-fitting protective clothing so nothing can catch on moving parts. |
![]() | Tie back long or loose hair so it can’t catch on moving parts. |
| Remove rings and jewellery so they can’t catch on the machine or the material, or reflect the beam. | |
![]() | Put away phones, headphones and other electronic devices so they don’t distract you or catch on moving parts. |
2. About the laser
| Laser classification | 4 – High power causing skin and eye injury from direct and reflected energy |
|---|---|
| Max optical power output | 5 W or 10 W, depending on your BluLaser version |
| Power input | 12v |
| Wavelength | 445-465nm |
| Control | TTL – Transistor-Transistor Logic |
Use only the 12 V power supply supplied with the laserConnecting the 24 V controller power supply may destroy the laser.
3. Hazards
Hazards that may arise when operating a laser include:
- burns from contact between the laser beam and your body
- severe eye damage from looking at the light emitted from the laser, including reflected light
- fire, if material is exposed to the beam for too long or the power and speed settings are wrong
- toxic fumes from burning or etching certain materials, which can harm your lungs if inhaled.
4. Materials you must not cut or engrave
Some materials can catch fire spontaneously or give off toxic fumes when exposed to the laser beam. The following materials are NOT safe to cut or engrave. This list is a guide only and is not complete.
- Leather and artificial leather containing chromium (VI)
- Carbon fibre
- Polyvinyl chloride (PVC)
- Polyvinyl butyral (PVB)
- Polytetrafluoroethylene (PTFE/Teflon)
- Beryllium oxide
- Any material containing halogens (fluorine, chlorine, bromine, iodine or astatine), epoxy or phenolic resins
5. Before you connect power to the laser
- Check that the work area and walkways are clear of slip and trip hazards.
- Make sure a working, suitable fire extinguisher and a fire blanket are close by. New: They must be within arm’s reach of where you stand while the laser runs, not across the room.
- Make sure you can quickly switch off power to both the CNC and the laser.
- Make sure you know where all the machine’s controls are and how they work.
- Make sure all guards and safety devices are in place and secure.
- New: Consider fitting a laser-safe enclosure or laser-safe screens around the machine to block direct and reflected light.
- Make sure the laser module is attached to the mounting plate with both screws, and the mounting plate is secured to the CNC.
- Make sure the laser module lens points straight down at the waste board.
- Be aware of other people in the area and make sure it is clear before you start.
- Isolate the room: put a sign on the door warning that a laser is operating, and make sure nobody can walk in.
- Connect the laser signal wires to the CNC controller.
- Position your material.
6. While the laser is connected to power
- Never leave the laser while it is connected to power.
- Make sure laser safety glasses are worn by everyone in the room.
- Make sure fumes are properly ventilated.
- Make sure nobody can enter the area.
- Only operate the laser through computer control.
- Never program a job beyond the machine’s capacity.
- Check your CNC program before starting.
- Make sure the material is secured to the bed.
- Keep every axis clear of obstructions while the machine is cutting or engraving.
- Never try to remove material from the bed while the job is running.
- New: Never focus or adjust the laser module while the laser is firing. Stop the job and disconnect the laser power first.
- Never look directly at the beam, even when the laser is not firing.
7. After use
- Wait for the laser to stop and disconnect its power before you remove the material and waste.
- Disconnect the laser power when you finish, or whenever you leave the laser.
- New: Always remove the laser module before you use the CNC for routing.
8. Troubleshooting
| Problem | Check |
|---|---|
| Laser doesn’t fire | Check the laser’s signal wires are connected to the TTL and GND terminals of the CNC controller, and the 12 V power supply is connected to the laser. |
| Material catches fire or flares up | The power and speed settings are wrong for the material. Stop the job and correct the settings. Check the material isn’t on the list above, and avoid plywoods or other materials with adhesives that may become flammable. |
| Fumes are building up in the room | Improve the ventilation and use a fume extractor. Don’t laser plastics, which can give off harmful fumes such as chlorine. |
Need help?
Email adam@bluecarve.com.au with your machine model, size and a photo or short video of the problem. Owners also help each other in the BlueCarve owners group on Facebook.
Email adam@bluecarve.com.au with your machine model, size and a photo or short video of the problem. Owners also help each other in the BlueCarve owners group on Facebook.
Stuck on something? I’m Bingo. Answer a couple of questions and I’ll point you to the fix.
BingoBlueCarve troubleshooting helper
Still stuck? adam@bluecarve.com.au





