Plasma Safe Operating Procedure

Version 2.0 · Updated November 2026 · For Spark Plasma CNC
Back to all instructions

Read this procedure, and the manual supplied with your plasma cutter, before you use your Spark Plasma CNC. Keep a printed copy near the machine. Always follow any additional safety requirements from your plasma cutter’s supplier.

1. Required personal protective equipment

SignWhat to wear or do
Wear a welding helmet, face shield or goggles with a welding filter lens of the right shade for plasma cutting. As a guide, use shade 5 up to 40 A, shade 6 for 40–60 A and shade 8 for 60–80 A, and confirm the shade in your plasma cutter’s manual. Ordinary safety glasses do not protect your eyes from the arc. Anyone nearby while the CNC is cutting must also wear suitable eye protection.
Wear leather welding gloves.
Blue circle sign showing protective clothingWear long sleeves and long pants made of natural fibres such as cotton, wool or leather. Don’t wear synthetic clothing (polyester, nylon, fleece): sparks can melt it onto your skin. Keep clothing close-fitting so it can’t catch on moving parts.
Blue circle sign showing a head wearing earmuffsWear earmuffs or earplugs. Plasma cutting is loud.
Blue circle sign showing a safety bootWear sturdy leather shoes or boots to protect your feet from hot metal, sparks and dropped material.
Tie back long hair and remove rings and jewellery.

2. Hazards

HazardWhat can happen
Arc lightThe plasma arc gives off intense ultraviolet and visible light that can burn your eyes (“arc eye”) and skin.
FumesCutting produces metal fumes. Galvanised, coated or painted metal gives off toxic fumes.
Fire and burnsSparks and molten metal can start fires. Cut parts, offcuts and dross stay hot for a long time after cutting.
Electric shockThe plasma cutter uses high voltage at the torch. Wet conditions increase the risk.
Compressed airA damaged hose or fitting can whip or release air suddenly.
Hydrogen gasCutting aluminium over a water tray can release hydrogen gas, which can collect under the plate and ignite.
Moving partsThe gantry and torch move quickly and without warning.
NoisePlasma cutting is loud enough to damage your hearing.

3. Before you start

Work area and fire

  1. Check that the work area and walkways are clear of slip and trip hazards.
  2. Remove anything flammable from around the machine: rags, paper, cardboard, wood, solvents, fuel and gas bottles.
  3. Have a working fire extinguisher within reach.
  4. Restrict access to the room where your CNC is operating, and make sure anyone nearby is wearing suitable eye protection.
  5. Make sure you know where all the machine’s controls are and how they work, including the process stop button.

Ventilation

  1. Make sure there is good ventilation or fume extraction.
  2. Never cut galvanised, coated or painted metal without fume extraction.

Electrical

  1. Plug the plasma cutter into a correctly rated circuit, as stated in its manual.
  2. Attach the earth (ground) clamp to the workpiece or the table, on a clean surface without rust or paint.
  3. Only connect power to the plasma cutter once the vertical torch is attached to the Z axis with the torch facing straight down.
  4. Allow free-flowing air to the CNC controller.
  5. Keep the water tray, hoses and any spilt water away from mains power, the plasma cutter and the CNC controller.

Compressed air

  1. Supply dry, filtered air, regulated to the pressure in your plasma cutter’s manual. An air dryer and filter are recommended.
  2. Check the air hoses and fittings for damage, leaks and wear before each session.
  3. Purge any water from the air lines.

Water tray

  1. Fill the water tray up to the material.
  2. Take extra care when cutting aluminium over water: hydrogen gas can build up under the plate. Keep the water level up to the material, don’t leave aluminium offcuts and dross to collect in the tray, and keep the area well ventilated.

4. While operating

  1. Never leave the CNC unattended while it is cutting.
  2. Keep your hands and body a clear distance from the torch and gantry.
  3. Don’t look at the arc without a correctly shaded filter.
  4. Never touch the torch, nozzle or workpiece while the torch could fire.
  5. Never exceed your plasma cutter’s stated duty cycle.
  6. Watch for fires. Stop the job if anything near the machine starts to smoulder or burn.
  7. If something goes wrong, press the process stop button.
Isolate the power before changing consumablesSwitch off and unplug the plasma cutter (or switch off at the wall) before you change the nozzle or electrode, or touch the torch for any reason.

5. After use

  1. Switch off the plasma cutter and the CNC.
  2. Take care when handling material after cutting. Parts, offcuts and dross stay hot long after the cut finishes: use gloves or tongs.
  3. Check the area for smouldering material before you leave.
  4. Turn off and drain the air supply.
  5. Clean the rails and rack, and remove dross from the knife bed and water tray.

6. Troubleshooting

The full list is in the Spark Plasma Troubleshooting guide. These problems affect safety:

ProblemCheck
The plasma keeps firing after the cut is finishedOn Unimig plasma cutters, the 4T setting may be selected. Change to 2T.
The plasma only sparks off the surface and doesn’t cut throughAttach the earth clamp to the material on a clean surface. Check the feed rate isn’t too high and the amps aren’t too low. Purge water from the air hoses.
The water in the water tray smellsAdd Plasma Protector, or add algaecide until the smell goes. Mix it in a bucket of water first, then spread it evenly across the tray.
Need help?
Email adam@bluecarve.com.au with your machine model, size and a photo or short video of the problem. Owners also help each other in the BlueCarve owners group on Facebook.
0
0
Quote Request
Your cart is emptyReturn to Shop