Support

Help for BlueCarve CNC owners · Updated 21 November 2026
Start here: ask BingoBingo is our troubleshooting helper. Tell it what you have and what is happening, and it walks you through the fix from our guides. It is the quickest way to sort most problems.
How do you control your machine?

Prefer to read? The instructions page finds the guides for your machine, and the common problems are listed below.

1. Start here: your machine’s instructions

The instructions page asks a few quick questions (machine, motors, controller) and shows only the guides for your machine, in order. Every guide can be printed or saved as a PDF.

CNC routersAll router instructions: Bluey, Turbo, AXE and Trax set up, Easel, FluidNC and the TouchBLUE tablet, BluLaser.
Spark plasmaAll plasma instructions: set up, legs and water tray, troubleshooting.
First things to tryRead the message on the screen: it usually says what to do. Switch the tablet or computer off and on. Switch the machine off and on, wait for it to connect, then home. Check every plug is fully seated and the machine’s own power is on (a USB connection alone doesn’t power it).

2. Which machine do you have?

The fixes are completely different for the two kinds of BlueCarve router, so check this first.

FluidNC machineOlder USB machine
How to tellFluidNC sticker on the black controller box, and a 7″ TouchBLUE touch tabletArduino controller in a white, clear or blue box, connected to a computer by USB
How you run itEverything (homing, jogging, zero, running jobs) is done on the tablet. There is no computer control.From a computer, using Easel
HelpSection 3Section 4

3. FluidNC tablet machines: common problems

ProblemWhat to do
The tablet stays OFFLINE (red)Check the machine’s own power is on and wait about 30 seconds. The machine’s WiFi network is BLUECARVE, password bluecarve. Keep the tablet within a few metres of the controller, then restart the tablet.
The tablet’s screen is blankThe tablet needs power all the time it’s in use. Check the USB adaptor is switched on and try another USB-C cable.
The cutter only jogs towards one cornerThe machine hasn’t been homed yet. Tap Control > Actions > Home All after every power-on.
Homing crashes into the end, or failsOn the Status tab, hold a metal object against each limit sensor and check its LIMIT lamp lights. The cause is almost always physical: the sensor is too far from the part that triggers it, or off-centre.
An ALARM messageRead the message, fix the cause, then tap Clear Alarm. The full list is in the TouchBLUE manual. Alarm 15 (start-up or configuration problem) or error 152 (config invalid): contact support.
“Tool / mode mismatch”, or a job won’t startSpindle jobs use tool T0 and laser jobs T1. Switch to the right mode on the Status tab, or see Making G-code: troubleshooting.
A file isn’t listedTap Refresh on the Files tab. Use a microSD card of 32 GB or less, formatted FAT32, with the file in the top folder, ending in .nc or .gcode.
An axis moves the wrong way even though the dial or arrow is rightContact support: the axis direction is a machine setting.
Anything elseFluidNC set up: troubleshooting and the TouchBLUE manual: troubleshooting
Keep the tablet up to dateMany problems are already fixed in the latest tablet software. Turn on the tablet and check the version on its first screen, then update it with the updater in the FluidNC set-up guide. Updating keeps your settings. If the update fails with “Invalid head of packet (0xff)”, try a different USB data cable and USB port, with no hub, then run it again.

4. Older USB machines (Arduino, Easel): common problems

ProblemWhat to do
Easel won’t connect, or homing and probing problemsEasel set up: troubleshooting
Error 9, or the machine ignores jog commandsThe controller is still in alarm. Unlock it, home, then jog.
Alarm 9 when homingA limit switch wasn’t found. Check each switch, its plug and cable, and that the axis moves freely.
All limit switches show as triggeredWith the machine powered and connected, unplug the axis sensors one at a time. If unplugging one clears them all, that sensor is the problem.
An axis moves the wrong distance, direction or speed (for example X moves 10 times too far), or the controller “ding-dings” when plugged in but won’t connectThe controller’s settings have usually been overwritten by other software (UGS, CNCjs, gSender) or an imported profile. Follow Reinstalling GRBL and reverting settings. Don’t use it for a first-time setup, if there’s no “ding-ding” when you plug in, or if nothing changed and you only use Easel: contact support instead.
Random false alarms after using another programSome programs (for example gSender) switch on hard limits, which BlueCarve routers don’t use. Use Easel, which is the supported program for these machines.
Bluey: Z won’t move after the machine was movedSwap the X and Z drivers to see if the Z driver has failed, and check the shield is still pressed onto the Arduino.

5. Spark plasma: common problems

Is it a new setup or a new problem? For a new setup, follow the Spark plasma set up. For a new problem, start with the troubleshooting checklist.

ProblemWhat to do
It finds the material but doesn’t cutCheck the plasma cutter actually fired (the torch started) before looking at wiring or communication.
It pierces but won’t cut, or the cut fadesCheck the air pressure at the start of the cut, not just at idle. A quick-connect fitting that doesn’t open fully can drop it to about 2 bar. Use one pair of fittings, a short air line and inline water traps.
Height control (Z) problemsUsually the voltage setting. Check your cut settings against the plasma cutter’s manual.
Floating head or collision errors, random Y stallsSet all three floating-head sensors as close to the base plate as possible, at the same height.
Dross on small holesAs a rule of thumb, a hole needs a diameter of about twice the material thickness to cut cleanly.
Cut speed, pierce delay and heights don’t changeMyPlasm uses only the shape from your G-code. Set speeds, pierce delays and heights in MyMiniCAM. If you use SheetCam, use the MyPlasm post-processor.

Full guide: Spark plasma troubleshooting. Spark owners also help each other in the BlueCarve owners group on Facebook.

6. Power, spindle and electrical

ProblemWhat to do
Random stops in the middle of a job, or the spindle sags under loadOften a light-duty power lead and electrical noise. Use a heavy-duty extension lead (1.5 mm wires) and a powerboard with an EMI filter, and keep the machine’s power separate from other big tools.
VFD error codes (for example E004, H10, P192)These often need the VFD reset and reprogrammed for your spindle’s wattage. Email the code and your spindle’s power rating before changing any wiring.
Water-cooled spindle running hotPump ratings drop quickly with hose length and height. Time how long the water takes to fill a measured cup, first at the pump outlet, then at the end of the hose, and compare it with what the spindle needs.
A new collet nut doesn’t fitMeasure your spindle’s nut before ordering. The supplied ER11A nut is 13.3 mm, and some spindles use a different size.

7. Supported software and updates

MachineSupported software
Older USB machines (Arduino)Easel is the supported program. LightBurn or LaserGRBL can be connected directly for the BluLaser.
FluidNC machinesRun everything from the TouchBLUE tablet. Use any design program to export G-code: Easel is recommended (fewest issues), and LightBurn works as a G-code maker for laser jobs. No program can control a FluidNC machine from a computer.
WhatWhere
Update the TouchBLUE tabletUpdater in the FluidNC set-up guide, or touchblue.pages.dev
TouchBLUE tablet manual and videoTouchBLUE tablet manual
Which design program to use, and how to save G-code for FluidNCMaking G-code for your FluidNC CNC
Your first job in Easel (free)Name plaque, step by step
Easel with an Arduino controllerEasel set up
BluLaserBluLaser set up. Air assist makes a big difference to cutting power and clean edges.
Router bits and toolingAdam’s Bits. BlueCarve owners get a discount: ask us for the code.

8. Upgrades and what we can’t do

  • FluidNC upgrade kit: closed-loop machines can be upgraded to the FluidNC controller and TouchBLUE tablet (conversion guide). It isn’t available for machines with open-loop motors.
  • Bigger table: an existing machine can’t be made bigger, because the frame, rails, gantry and drives are all sized to the table. We can offer a new machine at a discount, and you sell your current one yourself.
  • Other brands: we can’t fit a BlueCarve controller to another brand or an old home-built CNC. It isn’t plug-and-play.

9. Safety

Read the safe operating procedure for your machine before you use it, and keep the emergency stop within reach whenever the machine is moving.

10. Contact support

Email adam@bluecarve.com.au. To help us answer quickly, include:

  • your machine model and size (for example Turbo 1.5 x 1.5);
  • the controller (Arduino or FluidNC) and the software you use (Easel, the TouchBLUE tablet, LightBurn, MyPlasm…), with the tablet’s version number if you have one;
  • what you were doing, what changed recently, and the exact message or alarm on the screen;
  • a photo or short video of the problem, and of the wiring if it’s an electrical problem.

You can also use the contact form. Owners help each other in the BlueCarve owners group on Facebook, which is a good place to share projects and tips.

0
0
Quote Request
Your cart is emptyReturn to Shop